Our trade counter service provides you with access to a friendly and efficient service and advice. Please note - ideally we ask for 30 minutes’ notice to be sure you aren’t kept waiting. How do I return faulty items? Each of the bearings will be equally loaded at 100 lb., because the bearings are mounted at each corner of the saddle, and the center-of-gravity of the mass is centered fore-aft and left to right. Each of the bearing carriages can handle 500 lb of maximum radial loading, so an adequate life is calculated here because the bearings are loaded within the 20 to 50% range of total capacity.

Our Customer Service Team is available from between 7 am and 5 pm, Monday to Friday on 0800 594 44 44. Do you have any customer testimonials? DC MOTOR COMPATIBLE ] : With the wheel structure designed to be compatible with DC Motors, you can mount it with any DC motor you want.This wheelset is designed to adapt to the various motors you use in your robot projects. It comes with shaft adapters compatible with 3mm, 4mm D type shaft motors and L type plastic gearmotors. In this way, it offers the opportunity to use it with many engines. Duty cycle: The duty cycle parameter must consider the full motion of the saddle through a complete cycle, which is most often two times the stroke plus idle operations in a desired amount of time. The stroke of the application is the length of complete overall movement in one direction along a linear path. Typically, the duty cycle parameter is organized as the number of cycles required per minute.

is reasonably adequate for the Thames, but for a newcomer it may be best not to venture out while there are any boards displayed. Once you've a bit of experience under your belt, yellow decreasing is worth a go and mebe move up to yellow increasing after you've had a season's thouough experience. Orientation: The mounting orientation of the ways is critical for setting up the loading parameter because the saddle could be moving horizontally, vertically, along a wall-mount, or even in an inverted position. For best performance, manage the loading of the application with the strongest part of the bearing system. For example, the radial ball-bearing slider should be oriented to carry the load radially, not axially. Now make a linear-guide selection After selecting a system, assemble the parameters to properly size it. For each movement in a linear guideway system, consider the following parameters: stroke, load, speed, duty cycle, mounting area, and mounting orientation. Size the linear-guide system I have tried measuring the speed of floatsam by walking at pace with it using a gps. It’s around 2.5-2.8 mph (at least on the surface). I have been told she will make 3.8-4.5 mph. In theory it seems fine as I only want to go 1 mile downstream to empty the holding tank before winter and fuel up. GET SPEED TO YOUR ROBOTS ] : This wheelset is designed to adapt to the various motors you use in your robot projects. If you want to speed up your robot projects, these wheels will satisfy you.Of course, you could always move to another well known marina further upstream where the entrance is much, much wider..... The mounting area also needs to take into account the substrate or framing system for holding the guideway. The bearing footprint is the distance from the front of one carriage to the rear of the farthest carriage along one linear guideway. Many profiled shafts have to be mounted to completely machined and ground surfaces to properly meet the program requirements for precision. Other designs can be applied directly to structural aluminum or tubular framing without losing capacity or rigidity. To select which of the rails work best for an application, first, analyze the system’s specific needs. Next, understand the customer’s requirement or program guidelines, which include the number of axes, repeatability, tolerance, and accuracy required to achieve the end result. Finally, consider environmental contamination, such as dust, water, fibers, and other substances.

In your case move over to the right - as far as the mud will allow and point the bow to the rather narrow and not vert straight entrance and gun it.... For you paint's sake get a couple of proper sea going fenders and fix them forward (tow because you'll probably hit the entrance on the other side as well..

Customer Service

DESIGNED FOR PROJECTS ] : You can use these wheels in various projects. It comes with shaft adapters compatible with 3mm, 4mm D type shaft motors and L type plastic gearmotors. In this way, it offers the opportunity to use it with many engines. Our next day, nationwide delivery service is provided by Parcelforce & Tuffnells who enable us to provide you with a reasonably priced, consistent delivery service.